Clear corner install
I bought mine from www.vertexracing.com
http://img.photobucket.com/albums/v1...Corners003.jpg I used the chrome coated amber bulbs from www.autolumination.com http://img.photobucket.com/albums/v1...Corners004.jpg Tools needed: small ratchet 1/4 drive 9/32 socket or nut driver 10mm socket 3/8 drive ratchet with extension and swivel BEER and patience First get the front of the car off the ground....I used Rhino ramps but I suppose you could lift each side individually. (purple rugs not necessary ) http://img.photobucket.com/albums/v1...Corners002.jpg Now using the 9/32 socket you need to remove the front corner spoiler and the black close out panel. http://img.photobucket.com/albums/v1...Corners010.jpg You will be able to see the 9/32 screws that secure the light in place....you only need to remove the one closest to the outside of the car as the other 2 hold the fixture to the plastic mount which you will see when it is removed...next you need to push the brake cooling duct down and out of your way so you can reach the 10mm screw securing the front part of the light...this is a beotch and also where the ratchet with swivel comes in handy. After the screws are out there is a small reatining spring holding the fixture in place..carefully remove it from the light and leave the other end hooked up.....yeah I know..you dropped it its easy to reinstal and it slides into a notch in the back of the black mount for the light....its pretty self explanatory. http://img.photobucket.com/albums/v1...Corners013.jpg http://img.photobucket.com/albums/v1...Corners014.jpg Now you have this http://img.photobucket.com/albums/v1...Corners012.jpg take the remaining 9/32 screws out and remove the black mount from the light fixture http://img.photobucket.com/albums/v1...Corners011.jpg http://img.photobucket.com/albums/v1...Corners015.jpg Now attach the new light to the black mount http://img.photobucket.com/albums/v1...Corners016.jpg Ok...wasn't that fun??? Now the real fun begins putting it back in before you do anything else put your new bulbs in the socket. Carefully slide the new fixture up into place and reinstal the bulbs and re-attach the spring...(dropped it again didn't ya ) Now slide the fixture in place and this is where it gets fun...reach up and move the brake duct out of your way enough to jam your hand (which doesn't fit) into the opening and get the 10mm screw started on the front part of the new light. Now move around front and tighten with the 10mm socket using the ratchet with swivel attached....this is where patience and beer comes in handy Now reinstall the 9/32 screw on the other end. Check to make sure the lights work before re-installing the closeout panel and spoiler. You are all set. |
Now....do the other side.
Pics of finished work. I had the turn signal on to show different levels of brightness. http://img.photobucket.com/albums/v1...Corners017.jpg http://img.photobucket.com/albums/v1...Corners018.jpg |
I think I will add that to the list of things to do.....Thanks. :rolleyes: ;)
Just when you think your close to being done modding.....:hehehe: |
Quote:
|
Whoo-hoo..made someone spend money :lmao:
|
Quote:
|
Cool Mod. :thumbsup: now we need the clear side markers,3rd brakelite clear and don't forget the diamond cut backup lite and you will be rockin:dancer01: BTW the Silver Star lites work great with clear fronts too
|
|
Quote:
|
Hi Pewter, nice post. Just to let you know you made another guy spend some money this week . I ordered the clear corners yesterday and now trying to track down the chrome coated amber bulbs. I also ordered the clear side markers (http://www.coolights.com/Chevy-Corve...p_923-681.html) and will be looking for red bulbs.
|
All times are GMT -4. The time now is 05:35 PM. |
Powered by vBulletin® Version
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.