The ALL Florida Online Corvette Club








Corvette Top Sites

Go Back   The ALL Florida Online Corvette Club > General Corvette Forums > Maintenance, Mods, & Tips

      Photo Gallery Screen Saver!      

Maintenance, Mods, & Tips Mods | Tips | Repairs & Troubleshooting

Reply
Thread Tools Display Modes
Unread 03-04-2020, 04:33 PM   #1
Rich Z
Internet Sanitation Engineer
 
Rich Z's Avatar
 
Join Date: Mar 2006
Location: Crawfordville, FL
Posts: 15,123
Name : Rich Zuchowski
Rich Z will become famous soon enoughRich Z will become famous soon enough
Default Harbor Freight shop press

Been looking at one of these shop presses from Harbor Freight for a while now, so I figured it might come in handy while working on the exhaust system on the vette. I believed the flanges on the exhaust pipe that attaches to the catback pipes were distorted from the number of times they have been disconnected and then retightened, so this could help me try to straighten them out.

So the unit went on sale and I was able to use a 20% off coupon, so why the heck not? All I needed was a good reason to buy one.

Pretty easy to put together, with Connie's help, and I decided to put wheels on it so I could move it around as needed. Getting pretty tough to allocate a dedicated space for anything in the garage these days.



While looking for reviews of the press online, I noticed that some people had done some mods that seemed like it would make the press easier to work with. So before actually using the thing, I thought I would implement a few of them that seemed the most practical.

First off I heard people complain that those support plates sometimes had a tendency to fall off. They are pretty solid and heavy, so one hitting your foot would probably mean a bad day for your toes. So someone was putting in pins on the underside to keep the plates from slipping off the rails. I looked at this and figured out that instead of four pins, just 2 would do the job just fine. Quarter inch press fit roll pins worked just fine for this. Used the drill press to drill and chamfer the holes, then actually used the press itself to press them into place. I just used the opposite plate to control the depth of the fitting of the pins.



Next, I didn't want to have to use that long handle for the pneumatic press itself, as it would just wear you out if you had to use it much. So I had some 1.5 inch aluminum rod stock that I turned down on my mini lathe and made a shorter handle to work with.





I made the turned down insert end tapered so that the handle fits in there pretty snugly, and I can pretty much just keep the handle in place as I am working with the press. Also covered the grip with a cloth tape I had laying around that seems to work well. I considered knurling the handle, but I thought that would wear on the skin of my hands after a while. That cloth wrap is a whole lot more comfortable feeling. I don't imagine I would need the long handle for more leverage for most things I am likely to use the press for.

Next I wanted to put a permanent handle on the valve that is used to release the pressure on your work. Since I wasn't using that long handle, and didn't want to cut slots into that short handle I made, I decided to use some more 1.5 inch aluminum rod to create a handle that would be easy to grip and work well while I am playing around with trying to position the pressure ram where I wanted it to be.



Everything seems to work as it should with the mods, and I actually did work on those exhaust flanges a few days ago. Seems to have straightened them right up, and I don't have that slight bow in the center that I used to have. Unfortunately I was feeling way too lazy to pull off those catback pipes from the turbos, so I'm hoping just flattening out the one side of each flange will be good enough. We'll see when I do a leak test, I suppose. The exhaust is all put together right now, but when I went to do the leak test yesterday I discovered that the battery in the car was dead from sitting for too long. The car does like to be paid attention to rather often, it seems.

Incidentally, this press actually came in pretty handy just as a sort of shop vice to hold items when I needed to work on them. For instance, using a wire brush to clean off the flanges and the slip joints on the pipes was a lot easier with them being held in place by the arms of this press. And I needed to expand some of the slip over joints, and the press really helped with holding the pipes still while I was doing that chore.



So all in all, I think this was a pretty good investment. I'm pretty sure taking those pipes to a machine shop to have those flanges trued would have cost me at least what this press cost.
__________________
Rich Z is offline   Reply With Quote
Unread 03-04-2020, 06:13 PM   #2
85vette
Senior Member
 
85vette's Avatar
 
Join Date: Mar 2007
Location: On the road
Posts: 2,111
Name :
85vette will become famous soon enough
Default

The quality of their tools has definitely improved over the years. I bought an air compressor back in 2011 to run air tools and air up tires at my brother’s farm and it’s still working good. It’s one of the upright models, 3 or 4 hp and 130 psi I believe. Only paid around $149 IIRC.
__________________
I Have Noticed That A Lot Of People Demanding Free Stuff Are Not Wearing Work Boots.
85vette is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 14 (0 members and 14 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
keeping the shop floor clean etc. grumpyvette Maintenance, Mods, & Tips 1 03-09-2012 01:41 PM
Insurance/body shop help needed dementeddigital General Corvette Discussions 16 01-03-2011 05:42 AM
Our Annual List Of Where To Get Your Corvette Fixed RSS Feed Tech and How-To Articles 1 08-06-2010 02:56 PM
2009 Corvette Shop Guide - Our Annual List Of Where To Get Your Corvette Fixed RSS Feed Tech and How-To Articles 0 05-26-2009 03:43 PM
Timber Wolf Speed Shop C2 Build - The Timber Wolf C2 Finale RSS Feed Tech and How-To Articles 0 05-06-2009 10:00 PM


All times are GMT -4. The time now is 10:47 AM.


Powered by vBulletin® Version
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Page generated in 0.03715301 seconds with 12 queries
All material copyrighted by CorvetteFlorida.com and
the respective owners of the material posted.