The ALL Florida Online Corvette Club








Corvette Top Sites

Go Back   The ALL Florida Online Corvette Club > General Corvette Forums > Tech and How-To Articles

      Photo Gallery Screen Saver!      

Tech and How-To Articles This is an RSS feed from Corvette Fever's website to bring in links to tech articles and How To writeups.

Reply
Thread Tools Display Modes
Unread 03-05-2008, 08:52 AM   #1
pewter99
This place cracks me up
 
pewter99's Avatar
 
Join Date: May 2006
Location: CorvetteForum Mod
Posts: 322
Name :
pewter99 is on a distinguished road
Default #### C5 Clear corner light install ####

I installed some new clear corner lights from Vertex Racing www.vertexracing.com





I used the chrome coated amber bulbs from www.autolumination.com


Tools needed:

small ratchet 1/4 drive
9/32 socket or nut driver
10mm socket
3/8 drive ratchet with extension and swivel
BEER and patience

First get the front of the car off the ground....I used Rhino ramps but I suppose you could lift each side individually.





Now using the 9/32 socket you need to remove the front corner spoiler and the black close out panel



You will be able to see the 9/32 screws that secure the light in place....you only need to remove the one closest to the outside of the car as the other 2 hold the fixture to the plastic mount which you will see when it is removed...next you need to push the brake cooling duct down and out of your way so you can reach the 10mm screw securing the front part of the light...this is a beotch and also where the ratchet with swivel comes in handy. After the screws are out there is a small reatining spring holding the fixture in place..carefully remove it from the light and leave the other end hooked up.....its easy to reinstal and it slides into a notch in the back of the black mount for the light....its pretty self explanatory.






Now you have this




take the remaining 9/32 screws out and remove the black mount from the light fixture





Now attach the new light to the black mount





before you do anything else put your new bulbs in the socket.

Carefully slide the new fixture up into place and reinstal the bulbs and re-attach the spring...

Now slide the fixture in place and this is where it gets fun...reach up and move the brake duct out of your way enough to jam your hand (which doesn't fit) into the opening and get the 10mm screw started on the front part of the new light. Now move around front and tighten with the 10mm socket using the ratchet with swivel attached....this is where patience and beer comes in handy Now reinstall the 9/32 screw on the other end. Check to make sure the lights work before re-installing the closeout panel and spoiler. You are all set.

Now....do the other side.

Pics of finished work. I had the turn signal on to show different levels of brightness.





pewter99 is offline   Reply With Quote
Unread 06-21-2017, 02:48 AM   #2
Platero
Member
 
Join Date: Jun 2017
Location: Miami
Posts: 1
Name :
Platero is on a distinguished road
Default

Quote:
Originally Posted by peewter99 View Post
I installed some new clear corner lights from Vertex Racing www.vertexracing.com





I used the metadrol from here chrome coated amber bulbs from www.autolumination.com


Tools needed:

small ratchet 1/4 drive
9/32 socket or nut driver
10mm socket
3/8 drive ratchet with extension and swivel
BEER and patience

First get the front of the car off the ground....I used Rhino ramps but I suppose you could lift each side individually.
Does anyone know where I can get some of these clear corner lights these days?

Last edited by Platero; 11-20-2017 at 02:22 AM.
Platero is offline   Reply With Quote
Unread 06-21-2017, 07:15 AM   #3
mrr23
The Alignment Guy
 
mrr23's Avatar
 
Join Date: Aug 2007
Location: orlando, fl
Posts: 1,337
Name : Robert J Hinton
mrr23 is on a distinguished road
Default

http://www.jwmotorsportsllc.com/C5-F...of-2_p_99.html
__________________
the alignment guy
mrr23 is offline   Reply With Quote
Unread 01-28-2019, 02:45 AM   #4
rubyatiy
Member
 
Join Date: Jan 2019
Location: San diego
Posts: 1
Name :
rubyatiy is on a distinguished road
Default


These may be the range where you can justice the efforts with or without affects
rubyatiy is offline   Reply With Quote
Unread 02-22-2019, 05:47 AM   #5
Jeadiel
Member
 
Join Date: Feb 2019
Location: california
Posts: 1
Name :
Jeadiel is on a distinguished road
Default

Quote:
Originally Posted by pewter99 View Post
I installed some new clear corner v tight gel review lights from Vertex Racing www.vertexracing.com





I used the chrome coated amber bulbs from www.autolumination.com


Tools needed:

small ratchet 1/4 drive
9/32 socket or nut driver
10mm socket
3/8 drive ratchet with extension and swivel
BEER and patience

First get the front of the car off the ground....I used Rhino ramps but I suppose you could lift each side individually.





Now using the 9/32 socket you need to remove the front corner spoiler and the black close out panel



You will be able to see the 9/32 screws that secure the light in place....you only need to remove the one closest to the outside of the car as the other 2 hold the fixture to the plastic mount which you will see when it is removed...next you need to push the brake cooling duct down and out of your way so you can reach the 10mm screw securing the front part of the light...this is a beotch and also where the ratchet with swivel comes in handy. After the screws are out there is a small reatining spring holding the fixture in place..carefully remove it from the light and leave the other end hooked up.....its easy to reinstal and it slides into a notch in the back of the black mount for the light....its pretty self explanatory.






Now you have this




take the remaining 9/32 screws out and remove the black mount from the light fixture





Now attach the new light to the black mount





before you do anything else put your new bulbs in the socket.

Carefully slide the new fixture up into place and reinstal the bulbs and re-attach the spring...

Now slide the fixture in place and this is where it gets fun...reach up and move the brake duct out of your way enough to jam your hand (which doesn't fit) into the opening and get the 10mm screw started on the front part of the new light. Now move around front and tighten with the 10mm socket using the ratchet with swivel attached....this is where patience and beer comes in handy Now reinstall the 9/32 screw on the other end. Check to make sure the lights work before re-installing the closeout panel and spoiler. You are all set.

Now....do the other side.

Pics of finished work. I had the turn signal on to show different levels of brightness.





Does anyone know where I can get some of these clear corner lights these days?

Last edited by Jeadiel; 03-04-2019 at 01:25 AM.
Jeadiel is offline   Reply With Quote
Unread 02-22-2019, 05:57 PM   #6
mrr23
The Alignment Guy
 
mrr23's Avatar
 
Join Date: Aug 2007
Location: orlando, fl
Posts: 1,337
Name : Robert J Hinton
mrr23 is on a distinguished road
Default

Quote:
Originally Posted by Jeadiel View Post
Does anyone know where I can get some of these clear corner lights these days?
not really hard to find it when you use a search engine with key phrase c5 clear corner lens

amazon

https://www.amazon.com/Chrome-Housin...06602711&psc=1

ebay

https://www.ebay.com/i/282744388203?chn=ps
__________________
the alignment guy
mrr23 is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
C5 Corvette Callaway Billet Aluminum Throttle Body Install - Moving More Air RSS Feed Tech and How-To Articles 0 10-04-2007 01:05 AM
Wrapping It Up: 1965 Chevrolet C2 Corvette Carpet and Insulation Install RSS Feed Tech and How-To Articles 0 10-04-2007 01:05 AM
all clear running lights for a c5 ClockworkC5 Maintenance, Mods, & Tips 12 03-06-2007 08:28 AM
Clear Coat? Pres712 Detailing 3 12-22-2006 01:46 PM
Clear corner install pewter99 Maintenance, Mods, & Tips 10 07-17-2006 10:18 PM


All times are GMT -4. The time now is 07:26 AM.


Powered by vBulletin® Version
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Page generated in 0.05369306 seconds with 13 queries
All material copyrighted by CorvetteFlorida.com and
the respective owners of the material posted.