Hey guys, I'm wanting to sell my car or do a partial trade for a built F-body. Reason for selling is I'm getting married in April and have flat out just spent too much on the car. I bought it last summer and the engine starting having problems two weeks later and eventually was a total loss. The car just finished having a built LS7 installed last Friday. It will be towed to my tuner today (2/18/15) where it will receive a fresh and safe tune. It will have zero street miles on the new motor before getting the tune. The car will be ready to hop in and drive with no problems when the buyer picks it up. This car is not a garage queen. It's meant to be driven and enjoyed. It doesn have a few scratches here and there. No dents or major damages.
Here is a quick list of the mods:
Exterior:
MTI spliter with brake duct vents to front rotors[bottom pick-up]
MTI rear spoiler
RPI ZR1 side skirts
LG Vented Hood-Custom Painted insert/pinstripe]
Chevy SS Screen Package to fender vents
Katech-four position hold down pins to hood
427 Badge treatment to hood
HID Low Beams/Driving lights
Clear bra on nose / Vinyl wrapped the roof and halo black to match splitter, side skirts, rear spoiler (has a few places chipping)
Interior:
Custom Cobalt Red leather underdash/doors
Custom Painted black: Dash panel/door/switch gear/center console/steering wheel inserts.
DSV Interiors-Shift boot/ebrake boot/ebrake handle/armrest/waterfall/d-sport steeringwheel – Black Alcantera w/red stitching
External Gauges-twin pod-Transmission Temp and Fuel/air Ratio
Pfadt Race Engineering Bolt-In Chassis Bar - Red
Navigation System/XM-Satillite Radio
GM PAL installed - IPOD hookup in Glove Box
Elect Tilt and Telescope Wheel
Motor:
OLD SETUP
427 LS-7- Modified Heads: Custom 5 position Valve job/ Custom Springs[dual]/ported and polished[intake/exhaust]-milled-@12.5:1 comp/93 octane
Harland Sharpe Rockers
VetteDrs-"Sick-Stick" Cam#3/titanium retainers
HPSALES of Florida - Tune
LSXR-102MM Intake Manifold
Nick Williams 102MM Throttle Body
Calloway Cold Air intake
Lingenfletter 11 Quart Dry sump tank
American Racing 1-7/8 Racing Headers
PCV oil Catch can
Mustang DYNO – 580HP – 570ft/lbs – about same power as STOCK ZR1 on this dyno.
Vette doctors dyno - 591/541 corrected to 611/560
NEW SETUP
Everything listed above but with:
wiseco pistons
callies crank and rods
all new bearings and parts never used
ARP head studs
new redone LS7 heads ported and new valves, bronze guides, milled.
new BTR stage 3 cam with BTR .660 lift duel springs and ti retainers.
Suspension/Driveline:
New Clutch at 32,500 miles... Twin Disc McLoed - HPSALESFLORIDA
Pfadt Adjustable Coilover Shocks
Pfadt Solid Bushings to A-arms/Steering Rack
Pfadt Street Sway Bars[First Series-fully adjustable]
Pfadt Competition Sway Bar Pillow Blocks
Pfadt Bolt-In Chassis Bar
Pfadt Solid Transmission and Motor Mounts
Pfadt Street/Track Alignment
LG Competition Tunnel Plate
MTI Six-Shooter Short-Throw Shifter-Custom Jake logo ****
Brakes:
Coleman Two Piece Rotors
Hawk HP PLUS one piece pads - some noise but have tried Carbotech AX-6 (way too noisy) and stock pads just don't stop the car like a track pad.
Wheels:
Forgeline ZX3-R Fully Polished Aluminum Wheels- 18/19" -10.5" Front and 12.5" Rear
There are several C6Z's for sale around the same price with built motors. The difference is mine has 1000's and 1000's in suspension, exterior, and interior mods as well. I will sell outright for $48,000 but will also trade. I know it would be much easier financing my car if you added a trade to the deal. If you have a 15,000 car you can get financed for 33,000 for mine all day long. Ideally I'd like to trade for a built F-body with atleast 600rwhp. Trade value must be $20,000 or less. I want to be very clear on this next part...your trade must be in perfect working condition. No projects! Must need nothing other than to hop in and enjoy. Feel free to PM me with any questions or concerns. I'd like to keep this thread clean.
Thanks for looking!
Attached Images
Source...