|
Performance Tuning Beginner and advanced tuning | Tools of the trade |
|
|
11-07-2009, 10:53 AM
|
#1
|
www.revxtreme.com
Join Date: Apr 2006
Location: Bradenton
Posts: 1,171
Name : Tracy Lewis
|
Free tune analysis with dyno session!
Bring your car in for a dyno session, and we will not only give you the standard printout of rear wheel HP & TQ, but a tune specialist will log the runs and do an in-depth analysis of your current tune.....air fuel ratio throughout the run, timing tables, fuel trims, etc. and discuss how & if a tune would be a good choice & what gains in power & fuel economy you could expect. And as an added bonus, we will credit your dyno fee towards the full tune cost AND discount it all another $50 on top of it all!!
Call to schedule: 941-753-5255
__________________
Tech Support for most anything.
|
|
|
01-20-2010, 09:39 AM
|
#2
|
Deceased
Join Date: Jan 2010
Location: Sunshine State
Posts: 1,268
Name : Bob Korreck
|
Hey Tracy, don't you have an occasional dyno day?
|
|
|
01-20-2010, 09:50 AM
|
#3
|
www.revxtreme.com
Join Date: Apr 2006
Location: Bradenton
Posts: 1,171
Name : Tracy Lewis
|
Quote:
Originally Posted by Bob K
Hey Tracy, don't you have an occasional dyno day?
|
Next one is this Sat, 23rd....but I'm also trying to get to the track get a few customer cars dialed in.
__________________
Tech Support for most anything.
|
|
|
01-20-2010, 10:22 AM
|
#4
|
Deceased
Join Date: Jan 2010
Location: Sunshine State
Posts: 1,268
Name : Bob Korreck
|
I know, Dan is one of them. Regarding my problem, the EBCM went south and when I bring it up on the converter at 1400 the engine starts cutting out. It has to be TC right? I cannot disable it. Don't think I can run it like this.
I really want to make one of your dyno days just to see if I can improve my tune. Shift points, timing......
|
|
|
01-20-2010, 01:03 PM
|
#5
|
www.revxtreme.com
Join Date: Apr 2006
Location: Bradenton
Posts: 1,171
Name : Tracy Lewis
|
Quote:
Originally Posted by Bob K
I know, Dan is one of them. Regarding my problem, the EBCM went south and when I bring it up on the converter at 1400 the engine starts cutting out. It has to be TC right? I cannot disable it. Don't think I can run it like this.
I really want to make one of your dyno days just to see if I can improve my tune. Shift points, timing......
|
Log a scan of it when it is doing this & replay it looking closely at the TPS position & the timing. If it is shutting the throttle at the same time then I suspect it is the traction control. Read any codes & post them up so I can get a better idea....
__________________
Tech Support for most anything.
|
|
|
01-20-2010, 01:54 PM
|
#6
|
Corvette,GM Classic Freak
Join Date: May 2007
Location: Vero Beach FL/Old Fort NC
Posts: 1,052
Name : I'm Not Post'n in BOI
|
Quote:
Originally Posted by RevXtreme 1
Next one is this Sat, 23rd...
|
So whats it going to cost me?? I just possibly might could be in the hood on that date!
__________________
junk!!
|
|
|
01-20-2010, 02:37 PM
|
#7
|
Deceased
Join Date: Jan 2010
Location: Sunshine State
Posts: 1,268
Name : Bob Korreck
|
Quote:
Originally Posted by RevXtreme 1
Log a scan of it when it is doing this & replay it looking closely at the TPS position & the timing. If it is shutting the throttle at the same time then I suspect it is the traction control. Read any codes & post them up so I can get a better idea....
|
I just went out with street tires and my street tune in it. TC does not work. I am going to test with DR's. Maybe with the bad ECBM it can't handle a 17" tire. If it's still OK I will load my race tune and see what it does.
Something I left out is that I forgot my helmet Sat night so I had to really slow it down. I launched in 2nd and normally it's never a problem but that may have compounded another problem because of the EBCM. I'm thinking I will see you at the track Sat. We're going over to the other house tomorrow so I can be at Sunshine Fri night and Bradenton Sat.
|
|
|
01-20-2010, 03:38 PM
|
#8
|
Deceased
Join Date: Jan 2010
Location: Sunshine State
Posts: 1,268
Name : Bob Korreck
|
Quote:
Originally Posted by RevXtreme 1
Log a scan of it when it is doing this & replay it looking closely at the TPS position & the timing. If it is shutting the throttle at the same time then I suspect it is the traction control. Read any codes & post them up so I can get a better idea....
|
I just tested with DR's and it's fine. I will scan before I go to Sunshine and let you know. I think because I launched in 2nd and up on the converter that caused the problem due to the bad ECBM. I launched twice from idle in first and second and also from 1000 in second and all is good. Crazy.
Due to only one time shot Sat I didn't have any time to experiment and never thought there would be a problem.
The only code I can't clear is the 1214. Doesn't seem to be any other issues.
|
|
|
01-20-2010, 06:55 PM
|
#9
|
Deceased
Join Date: Jan 2010
Location: Sunshine State
Posts: 1,268
Name : Bob Korreck
|
Tracy, I put the scanner on it and got up on the converter. Throttle position stayed the same but timing went to -6. As long as I don't bump the converter it's fine.
See you Sat at the track.
|
|
|
01-21-2010, 09:36 AM
|
#10
|
www.revxtreme.com
Join Date: Apr 2006
Location: Bradenton
Posts: 1,171
Name : Tracy Lewis
|
Quote:
Originally Posted by Bob K
Tracy, I put the scanner on it and got up on the converter. Throttle position stayed the same but timing went to -6. As long as I don't bump the converter it's fine.
See you Sat at the track.
|
1214 sounds likke a shift solinoid issue, and that fact that the timing drops to -6 shows another issue related to traction control I believe. Goona take a bit more analysis to figure this one out.
__________________
Tech Support for most anything.
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -4. The time now is 12:25 AM.
|